J13 Monitor Connector Data:  SN-03, SN-05, SN-06, and SN-16
  -----------------------------------------------------------


                                              Rev.  18-Mar-2015


I believe that the 2 cards that you have access to in the
Test Rack are  SN-03  and  SN-16.   I actually found some
written MSU test data for SN-03  and I have the official
MSU test data for SN-16.

NOTE:  On SN-03 I know that I never installed the scaling
       attenuator for the backplane 5.0V monitor circuit.

       I strongly doubt that SN-03 has all of the scaling
       resistors installed for either the J13 readings or
       for the CANBus ADC readings to be correct.

       I would  NOT  use SN-03 to "prove" that the
       J13 DVM readings match the  CANBus uProcessor
       DCS data.

After the video meeting you read to me the DCS numbers for
2 cards running in USA15.  I believe that these are CMX
cards  SN-05 and SN-06.

Below please find the J13 Monitor connector data that I
have for cards: SN-03, SN-05, SN-06, and SN-16



 J13   Circuit  Expected      SN-03       SN-05       SN-06       SN-16
Loct. Measured    Value    10-Mar-14   24-Jun-14    7-Jul-14   31-Oct-14
----  --------  --------    --------    --------    --------    --------

  1    BSPT V     1.200 V    1.204 V     1.205 V     1.204 V     1.204 V
  2    BSPT I       -        0.032       0.035       0.029       0.030

  3  BF Core V    1.000      1.004       1.004       1.004       1.004
  4  BF Core I      -        0.096       0.165       0.168       0.178

  5  GTX_VTT V    1.200      1.204       1.203       1.205       1.205
  6  GTX_VTT I      -        0.032       0.105       0.106       0.106

  7  GTX_VCC V    1.030      1.028       1.032       1.033       1.034
  8  GTX_VCC I      -        0.040       0.111       0.116       0.117

  9  TP Core V    0.0        0.0         0.0         0.0         0.0  
 10  TP Core I      -        0.007       0.082       0.084       0.078

 11    3.3V V     3.300      3.307       3.308       3.309       3.310
 12    3.3V I       -        0.429       0.515       0.520       0.521

 13    2.5V V     2.500      2.505       2.505       2.505       2.505
 14    2.5V I       -        0.063       0.138       0.141       0.143

 15    5.0V V     3.684      4.946 *     3.643       3.642       3.639

 16   VREF_P V    1.250      1.256       1.251       1.253       0.743
        **      or 0.750


  Notes:   * Card SN-03 never had the scaling attenuator
             installed for the backplane 5.0V monitor
             circuit.

          ** On the initially production cards the VRef_P
             reference was set to mid scaler,  i.e. about
             1.250 Volts.  On production cards starting
             with SN 15  the VRef_P reference supply was
             set to its lowest value, about 0.750 Volts.

             Getting SN-03 ready to use was a rush job.
             I have little recorded data from its testing.
             I strongly doubt that it was tested under
             the same standard conditions as the
             production CMX cards,  e.g. what components
             were installed  (MiniPOD, SFP, TTCDec)
             and what firmware was loaded.
             I strongly doubt that SN-03 has all of the
             scaling resistors installed for either the
             J13 readings or the CANBus ADC readings
             to be correct.