# # This is a Key-In Components File for the # CMX-0 Common Merger Module Extended # ----=======------------------------------------ # # # Front-Panel Components # ------------------------ # # # Original Rev. 25-Aug-2011 # Previous Rev. 03-Jan-2013 # Most Recent Rev. ??-???-???? # # NOTE: revised again- MTP feedthroughs rearranged and raised # NOTE: other parts shuffled by 19 mm # NOTE: This document is stale- contact Dan Edmunds for updated version # # This is a revision of the Components file incorporating all changes made in order to # fit and distribute the components along the front panel. # # Some components have been moved, and some of the Dual LED units have been removed to # make room for 5 MTP optical feedthroughs. # # The two MDR_68 connectors are now used to provide additional attachments between the # PCB and the front panel. # # This Components file holds all of the parts that mount next # to or go through the CMX Front Panel. # # # Recall some of the keep-out areas: # # Top Handle Mounting Screw: X < 7.0mm and Y > 357.3mm # Bottom Handle Mounting Screw: X < 7.0mm and Y < 9.4mm # # Recall that the card is 9U i.e. 366.7mm tall in the Y dimension. # UNITS MM # # Board_Location # Ref Part_Number Symbol Geometry X Y Properties #----- ----------- ------ ------------------ -------------- ---------- # # Place the front-panel LEDs_Dual. # # CMM has a total of 24 LEDs but 4 of these are all for power. # We will start with 10 dual LEDs on CMX - only 1 will be for power. # All 10 of these dual LEDs are near the top of the front panel. # They start as high up as possible. These LEDs are spaced 5.00mm in Y. # # Note: After reserving positions for 5 MTP optical feedthroughs there is # enough room remaining for 5 dual LEDs # LED_Dual_1 LED_Dual_RR SY_JUNK led_dual_fp_smd 0.0 355.0 1 0 LED_Dual_2 LED_Dual_RR SY_JUNK led_dual_fp_smd 0.0 350.0 1 0 LED_Dual_3 LED_Dual_RR SY_JUNK led_dual_fp_smd 0.0 345.0 1 0 LED_Dual_4 LED_Dual_RR SY_JUNK led_dual_fp_smd 0.0 340.0 1 0 LED_Dual_5 LED_Dual_RR SY_JUNK led_dual_fp_smd 0.0 335.0 1 0 # Connectors for the Front-Panel CTP Output # # These are 68 pin 3M type MDR cable connectors for # the cable run to the Central Trigger Processor. # We start with these connectors placed right next # to each other. They are centered about 10mm under # the vertical center of the CMX card. These 2 # connectors are spaced 66.5mm in Y. # # # Note: These two MDR connectors have been moved 2.54 mm in the negative X # direction to place them against the inner surface of the front panel. # The Y positions are unchanged from the previous version of this file. # # Note: The X position listed here refers to the center of the PCB hole pattern. # The Y positions listed here refer to the center of the PCB hole pattern. # # Note: The resulting X positions of the #4-40 mounting holes should be 6.060 mm. J10 Conn_3M_MDR_68 SY_JUNK m3_68_pin_mdr_conn 5.14 206.5 1 180 J11 Conn_3M_MDR_68 SY_JUNK m3_68_pin_mdr_conn 5.14 140.0 1 180 # SFP Optical Transceivers - Optical Transmitters 1 Gbps to DAQ and RIO # # SFP1 and SFP2 are for the Base Function output to the # DAQ and RIO. SFP1 and SFP2 are located right next to each # other and they are above the CTP connectors. # # SFP3 and SFP4 are for the Topological Processor output to the # DAQ and RIO. SFP3 and SFP4 are located right next to each # other and they are under the CTP connectors. # # The adjaced SFP packages are spaced 17.0mm apart in Y. # The vertical center of the SFP package next to an MDR # connector is currently spaced 49.0mm from the MDR's vertical center. # # Note: The X-position of these units is unchanged from the previous version of # this file. # The Y positions are different: while adjacent SFP units are still 17 mm # apart, the SFP package next to an MDR connector is now spaced 42.0 mm # from the MDR's vertical center. SFP1 Conn_SFP_Optical SY_JUNK SFP_Optical 34.5 265.5 1 0 SFP2 Conn_SFP_Optical SY_JUNK SFP_Optical 34.5 248.5 1 0 SFP3 Conn_SFP_Optical SY_JUNK SFP_Optical 34.5 98.0 1 0 SFP4 Conn_SFP_Optical SY_JUNK SFP_Optical 34.5 81.0 1 0 # Place the front-panel JTAG + RS232 connector # # This a 2mm 2 row by 8 16 pin 4 wall # 90 degree solder tail header connector. # # This is 2 pins more than the normal Xilinx 2x7 # JTAG connector. These 2 extra pins are for # CAN-Bus microprocessor RS-232 connection. # # J12 is currently placed as low down on the # front panel as it is possible to go. # # This is a Molex 87833-1620 DK WM18864-ND connector. # # Note: This connector has been moved 2 mm in the negative X direction. # This connector has been moved 4 mm in the positive Y direction. # The coordinates listed here refer to the center of the 16 hole # pattern in the PCB. J12 Conn_2x8_Header SY_JUNK Conn_2x8_Header_90Deg 3.0 22.5 1 0