// // // // Shape Edit Section of the // -==========----------------- // // HTM Card Printed Circuit Board Geometry File // ------------------------------------------------ // // // Area Fills on Signal Layer 12 <--- // ---------------------------==== // // // // Original Rev. 27-Mar-2018 // Current Rev. 28-Mar-2018 // // // Notes: // // - These are Area Fills because they are on a Signal layer // in the Mentor design. // // - The principal power nets that are distributed // on Signal_12 are: // // ISO_12V // BULK_3V3 West of the BULK_3V3 Regulator U101 // // // // - These fills are kept back at least 4.5 mm from the // top and bottom edges so that the area fills will not be // exposed when the top and bottom edges are milled to // allow this card to fit into the crate card guides. // // - These fills are kept back at least 1mm from the front // and back edges to comply with normal decorum. // // - EVERYTHING in this Signal_12 fill file is repeated // on both the layers: DIELECTRIC_2 and SHAPE_EDIT. // See the bottom section of this file. // // - As of 27-Mar-2018 there are 2 shapes defined in this file. // // ISO_12V // // // // // // Net: ISO_12V // // Fill Layer: Signal_12 // // Location: ISO_12V Supply Module // // Resolution: Medium // $$initial([ 187.5, 246.0 ], , @nosnap ); // Start in the NE corner - go CCW $$terminal([ 85.0, 246.0 ] ); // Go most of the way West across the Top $$terminal([ 85.0, 220.4 ] ); // Go Down part of the the West Edge. $$terminal([ 156.0, 220.4 ] ); // Go East above the Bulk Supplies $$terminal([ 156.0, 165.0 ] ); // Go Down to near the top of the J2 Mezz Conn $$terminal([ 162.6, 165.0 ] ); // Go East to pick up the run through J2 Conn $$terminal([ 162.6, 141.0 ] ); // Go Down through the ISO_12V FPGA Mezz J2 pins $$terminal([ 118.0, 141.0 ] ); // Go West to get more width $$terminal([ 118.0, 80.0 ] ); // Go Down just East of the MiniPODs $$terminal([ 74.4, 80.0 ] ); // NO_MITER Go West to get to the West side // of the ISO_12V supply $$terminal([ 55.0, 60.6 ] ); // NO_MITER Go at 45 deg to the West edge // of ISO_12V supply $$terminal([ 55.0, 10.0 ] ); // Go Down the West edge of ISO_12V supply $$terminal([ 129.0, 10.0 ] ); // Go East under the ISO_12V supply $$terminal([ 129.0, 39.0 ] ); // Go Up the East edge of ISO_12V supply $$terminal([ 167.0, 39.0 ] ); // Go East to start the run UP $$terminal([ 167.0, 108.0 ] ); // NO_MITER Go Up through West part of J1 $$terminal([ 187.5, 125.0 ] ); // NO_MITER Go at an angle up to under J2 $$terminal([ 187.5, 246.0 ] ); // Go North up through the ISO_12V // section of J2 and back to home. $$path( "SHAPE_EDIT", 0.0 ); // // Net: BULK_3V3 // // Fill Layer: Signal_12 // // Location: Running West from the BULK_3V3 Regulator U101 // // Resolution: Medium // $$initial([ 155.0, 219.6 ], , @nosnap ); // Start in the NE corner - go CCW $$terminal([ 100.0, 219.6 ] ); // Go West across the Top of Bulk_3V3 Reg. $$terminal([ 100.0, 198.0 ] ); // Go South to get past the Bulk_2V5 Reg $$terminal([ 65.0, 198.0 ] ); // Go West under the Bulk_2V5 Reg. $$terminal([ 65.0, 240.0 ] ); // Go North to get to the top of the FP LEDs $$terminal([ 14.0, 240.0 ] ); // Go West to pickup the LED PU Resistors $$terminal([ 14.0, 114.0 ] ); // Go South to pick up PU Res, Drivers, LVDS $$terminal([ 45.0, 114.0 ] ); // Go East to get around RJ45 and Enet Magnetics $$terminal([ 45.0, 91.0 ] ); // Go South to get past RJ45 and Enet Magnetics $$terminal([ 25.0, 91.0 ] ); // Go West to get close to East end of J13 $$terminal([ 25.0, 70.0 ] ); // Go South to around J13 $$terminal([ 8.0, 70.0 ] ); // Go West far enough to pick up JTAG Bufs. $$terminal([ 8.0, 30.0 ] ); // Go South past the West edge of JTAG Bufs. $$terminal([ 54.0, 30.0 ] ); // Go East under the JTAG Buffers $$terminal([ 54.0, 61.4 ] ); // NO_MITER Go North past the West edge of ISO_12V $$terminal([ 73.6, 81.0 ] ); // NO_MITER Go at 45 deg to pick up MiniPOD 3V3 Filters $$terminal([ 73.6, 155.5 ] ); // Go North past all the MiniPOD Filters $$terminal([ 136.0, 155.5 ] ); // Go East over the the start of J2 $$terminal([ 136.0, 165.0 ] ); // Go North a little to clear J2 traffic $$terminal([ 155.0, 165.0 ] ); // Go East under the BULK_3V3 Regulator $$terminal([ 155.0, 219.6 ] ); // Go North up through the BULK_3V3 // regulator and back to home. $$path( "SHAPE_EDIT", 0.0 ); // // =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- // =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- // // Repete the above on design layer $$path( "DIELECTRIC_2", 0.0 ); // // =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- // =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- // // // Net: ISO_12V // // Fill Layer: Signal_12 // // Location: ISO_12V Supply Module // // Resolution: Medium // $$initial([ 187.5, 246.0 ], , @nosnap ); // Start in the NE corner - go CCW $$terminal([ 85.0, 246.0 ] ); // Go most of the way West across the Top $$terminal([ 85.0, 220.4 ] ); // Go Down part of the the West Edge. $$terminal([ 156.0, 220.4 ] ); // Go East above the Bulk Supplies $$terminal([ 156.0, 165.0 ] ); // Go Down to near the top of the J2 Mezz Conn $$terminal([ 162.6, 165.0 ] ); // Go East to pick up the run through J2 Conn $$terminal([ 162.6, 141.0 ] ); // Go Down through the ISO_12V FPGA Mezz J2 pins $$terminal([ 118.0, 141.0 ] ); // Go West to get more width $$terminal([ 118.0, 80.0 ] ); // Go Down just East of the MiniPODs $$terminal([ 74.4, 80.0 ] ); // NO_MITER Go West to get to the West side // of the ISO_12V supply $$terminal([ 55.0, 60.6 ] ); // NO_MITER Go at 45 deg to the West edge // of ISO_12V supply $$terminal([ 55.0, 10.0 ] ); // Go Down the West edge of ISO_12V supply $$terminal([ 129.0, 10.0 ] ); // Go East under the ISO_12V supply $$terminal([ 129.0, 39.0 ] ); // Go Up the East edge of ISO_12V supply $$terminal([ 167.0, 39.0 ] ); // Go East to start the run UP $$terminal([ 167.0, 108.0 ] ); // NO_MITER Go Up through West part of J1 $$terminal([ 187.5, 125.0 ] ); // NO_MITER Go at an angle up to under J2 $$terminal([ 187.5, 246.0 ] ); // Go North up through the ISO_12V // section of J2 and back to home. $$path( "DIELECTRIC_2", 0.0 ); // // Net: BULK_3V3 // // Fill Layer: Signal_12 // // Location: Running West from the BULK_3V3 Regulator U101 // // Resolution: Medium // $$initial([ 155.0, 219.6 ], , @nosnap ); // Start in the NE corner - go CCW $$terminal([ 100.0, 219.6 ] ); // Go West across the Top of Bulk_3V3 Reg. $$terminal([ 100.0, 198.0 ] ); // Go South to get past the Bulk_2V5 Reg $$terminal([ 65.0, 198.0 ] ); // Go West under the Bulk_2V5 Reg. $$terminal([ 65.0, 240.0 ] ); // Go North to get to the top of the FP LEDs $$terminal([ 14.0, 240.0 ] ); // Go West to pickup the LED PU Resistors $$terminal([ 14.0, 114.0 ] ); // Go South to pick up PU Res, Drivers, LVDS $$terminal([ 45.0, 114.0 ] ); // Go East to get around RJ45 and Enet Magnetics $$terminal([ 45.0, 91.0 ] ); // Go South to get past RJ45 and Enet Magnetics $$terminal([ 25.0, 91.0 ] ); // Go West to get close to East end of J13 $$terminal([ 25.0, 70.0 ] ); // Go South to around J13 $$terminal([ 8.0, 70.0 ] ); // Go West far enough to pick up JTAG Bufs. $$terminal([ 8.0, 30.0 ] ); // Go South past the West edge of JTAG Bufs. $$terminal([ 54.0, 30.0 ] ); // Go East under the JTAG Buffers $$terminal([ 54.0, 61.4 ] ); // NO_MITER Go North past the West edge of ISO_12V $$terminal([ 73.6, 81.0 ] ); // NO_MITER Go at 45 deg to pick up MiniPOD 3V3 Filters $$terminal([ 73.6, 155.5 ] ); // Go North past all the MiniPOD Filters $$terminal([ 136.0, 155.5 ] ); // Go East over the the start of J2 $$terminal([ 136.0, 165.0 ] ); // Go North a little to clear J2 traffic $$terminal([ 155.0, 165.0 ] ); // Go East under the BULK_3V3 Regulator $$terminal([ 155.0, 219.6 ] ); // Go North up through the BULK_3V3 // regulator and back to home. $$path( "DIELECTRIC_2", 0.0 );