//
//   File:  diff_pair_thru_1g
//
//   Date:  17-Jun-2015   original version  -  made for Hub Module
//
//          10-Jun-2016   current version  -  removed silkscreen reference designator
//
//          14-Jun-2016   Add the "Component_not_in_bom" attribute to
//                        Remove all instances of this component from the BOM.
//
//          27-Aug-2016    Remove the Silkscreen component outline.
//
//
//
//     One Pin Version of the Diff Piar Through PCB Stackup,
//
//     i.e.  this is just the Ground Pin to put at the end
//           of where you have used a set of the Three Pin components.
//
//
//     Note:  The pin to pin spacing is  1.00 mm  center-to-center.
//            for  signal-to-signal   and   signal-to-ground
//
//
//   Geometry for a  Ground Via  to complete a set of high-speed
//   differential via pairs - through board  signal via pair.
//
//
//
//   This is not a component that the assembly house installs on the
//   card so its Reference Designator is not shown in Silkscreen.
//
//   This component has the  Not in BOM  attribute.
//
//
//
//   Pins #1  needs to be tied to Gnd in the net list.
//
//
//
//



$abort_enable = @false;
$$lock_windows(@on) ;
$$snap_diagonal(@off) ;
$$snap_orthogonal(@off) ;



//----------------------------------------------------------------------------
//
//  Diff_Pair_Through   Ground Pin Geometry   (same as  0mm60 Via)
//
//  Special Small 0.60mm Land Diameter routing via for the  CMX  card.
//
//  The pin-stack  DIFF_PAIR_THRU_GND_PAD  is defined in the
//  geometry for the component  Diff_Pair_Through.
//
//----------------------------------------------------------------------------
//
//  Special Small 0.56mm Land Diameter pin pad-stack for the Hub Module.
//
//  This "via" is used for the High Speed Differential GTH signals that
//  run the whole way  (or most of the way) through the card stackup.
//
//  The pin-stack  DIFF_PAIR_THRU_SIG_PAD  is defined in the
//  geometry for the component  Diff_Pair_Through.
//
//----------------------------------------------------------------------------



//
//  Now the actual  DIFF PAIR THROUGH  Geometry
//

$$create_component("DIFF_PAIR_THRU_1G");

$$page(0.0, 0.0, 0.0, @mm, 0.0, 0.0, [0.0,0.0,'CO$DIFF_PAIR_THRU_1G'] );

$$point_mode(@vertex);


$$attribute( "COMPONENT_HEIGHT", "", , @scale , , [ 1.0,  0.0 ]);

$$attribute( "COMPONENT_OUTLINE_OVERHANG", "yes");

$$attribute( "COMPONENT_LAYOUT_SURFACE", "both");

$$attribute( "COMPONENT_NOT_IN_BOM" );


//
//  Component Outline  of the square body part of the connector
//

$$initial([   0.30,   0.30 ], , @nosnap );
$$terminal([ -0.30,   0.30 ]);
$$terminal([ -0.30,  -0.30 ]);
$$terminal([  0.30,  -0.30 ]);
$$terminal([  0.30,   0.30 ]);

$$attribute( "COMPONENT_PLACEMENT_OUTLINE", "", @mark, @scale );



//
//  Silkscreen Outline  of the square body part of the connector
//

$$template_line_style( @Solid );

// //$$initial([   0.40,   0.40 ], , @nosnap );
// //$$terminal([ -0.40,   0.40 ]);
// //$$terminal([ -0.40,  -0.40 ]);
// //$$terminal([  0.40,  -0.40 ]);
// //$$terminal([  0.40,   0.40 ]);

// //$$path( "SILKSCREEN", 0.10 );

//    Silkscreen  End of



//
//  Reference Designator  -  Is NOT shown in SilkScreen
//

// //$$text( "SILKSCREEN", "^$ref",  0.0,   0.0,  0.3, @CC, 0, 1.00, 0.10, "std", "None", 0.0, 0.0 );




//
//       Ground and Signal Pins in the Diff_Pair-Through
//      -------------------------------------------------
//
//
//         Pin #1
//         Ground
//


$$attribute( "COMPONENT_PIN_DEFINITION",     "1", , @scale , ,     [  -0.00,   0.00 ]);
$$attribute( "COMPONENT_PADSTACK_OVERRIDE",  "1, DIFF_PAIR_THRU_GND_PAD");