#
#               BULK_1V8  Supply
#
#            DCDC 6 Converter Nets
#          -------------------------
#
#
#                                   Original Rev.  27-Mar-2015
#                                    Current Rev.   2-Dec-2016
#
#
#
#   This file holds all of the nets for DCDC Converter 6.
#
#   This is the  BULK_1V8  supply   1.800 V  at  12 Amps.
#
#   This Hub Module supply uses a  GE_PDT012  converter.
#


#
#  Connect the converter's  V_Input, V_Output, and Ground  terminals:
#

NET  'ISO_12V'    DCDC6-2


NET  'GROUND'     DCDC6-3   DCDC6-7


NET  'BULK_1V8'   DCDC6-4




#
#  Connect this converter's INPUT Filter:
#

NET  'ISO_12V'   C1261-2   C1262-2   C1263-2   C1264-2
NET  'GROUND'    C1261-1   C1262-1   C1263-1   C1264-1

NET  'ISO_12V'   C1265-2   C1266-2
NET  'GROUND'    C1265-1   C1266-1




#
#  Connect this converter's  OUTPUT  Filter:
#

NET  'BULK_1V8'   C1271-1   C1272-1   C1273-1   C1274-1
NET  'GROUND'     C1271-2   C1272-2   C1273-2   C1274-2

NET  'BULK_1V8'   C1275-1   C1276-1   C1277-1       DZ1251-1
NET  'GROUND'     C1275-2   C1276-2   C1277-2       DZ1251-2





#
#  Ground this converter's unused SYNC terminal:
#

NET  'GROUND'   DCDC6-11




#
#  Connect the  ON_OFF  and  POWER_GOOD  terminals:
#
#  Recall:  The ON_OFF pin is Low active,  i.e. voltage low --> ON.
#           The POWER_GOOD is a common open drain signal
#

NET  'DCDC_6_OFF_ON'        DCDC6-1

NET  'DCDC_6_POWER_GOOD'    DCDC6-10




#
#  Connect the  RAMP_SEQUENCE  terminal:
#
#  Recall:
#
#     The output voltage tracks the scaled Vseq up to set point.
#     R1255 is the 20k Ohm series resistor.
#     R1256 is the scale shunt resistor to ground.


NET  'CONVERTER_RAMP'          R1255-2

NET  'DCDC6_RAMP_SEQUENCE'     R1255-1   R1256-2   C1252-2   DCDC6-9

NET  'DCDC6_SIG_GND'                     R1256-1   C1252-1




#
#  Connect this converter's Output Voltage Control resistor
#  between the  TRIM  and  SIG_GND  terminals:
#

NET  'DCDC6_TRIM'      DCDC6-6    R1252-2

NET  'DCDC6_SIG_GND'   DCDC6-13   R1252-1




#
#  Connect this converter's Remote Sense input
#  terminals  V_SENSE_PLUS  and  V_SENSE_MINUS:
#

NET  'BULK_1V8'   DCDC6-5

NET  'GROUND'     DCDC6-12




#
#  Connect this converter's Servo Loop RC components
#  between the  V_SENSE_PLUS  and  TRIM  terminals:
#

NET  'BULK_1V8'        C1251-1

NET  'DCDC6_LOOP_RC'   C1251-2   R1251-1

NET  'DCDC6_TRIM'                R1251-2




#
#  Connect the PMBus  to this converter and set its address
#  using the  PMBUS_CLK,  PMBUS_DATA,  SMB_ALERT,  ADRS0
#  and  ADRS1  terminals:
#

NET  'Hub_PMBus_SCL'     DCDC6-8

NET  'Hub_PMBus_SDA'     DCDC6-15

NET  'Hubs_SMB_Alert_B'  DCDC6-14

NET  'DCDC6_ADRS_0'      DCDC6-16   R1253-2

NET  'DCDC6_ADRS_1'      DCDC6-17   R1254-2

NET  'DCDC6_SIG_GND'     R1253-1    R1254-1





#
#  Connect the  Power Via Arrays
#

#
#   INPUT Via-Arrays
#

NET  'ISO_12V'    PVA1_dc6-1   PVA1_dc6-2   PVA1_dc6-3
NET  'ISO_12V'    PVA1_dc6-4   PVA1_dc6-5   PVA1_dc6-6

NET  'ISO_12V'    PVA2_dc6-1   PVA3_dc6-1



#
#   GROUND Via-Arrays
#

NET  'GROUND'     PVA4_dc6-1   PVA4_dc6-2   PVA4_dc6-3

NET  'GROUND'     PVA5_dc6-1   PVA6_dc6-1   PVA7_dc6-1

NET  'GROUND'     PVA8_dc6-1   PVA9_dc6-1



#
#   OUTPUT Via-Arrays
#

NET  'BULK_1V8'   PVA10_dc6-1   PVA10_dc6-2   PVA10_dc6-3
NET  'BULK_1V8'   PVA10_dc6-4   PVA10_dc6-5   PVA10_dc6-6

NET  'BULK_1V8'   PVA11_dc6-1   PVA11_dc6-2   PVA11_dc6-3
NET  'BULK_1V8'   PVA11_dc6-4   PVA11_dc6-5   PVA11_dc6-6

NET  'BULK_1V8'   PVA12_dc6-1   PVA13_dc6-1