#
#               BULK_3V3  Supply
#
#            DCDC 8 Converter Nets
#          -------------------------
#
#
#                                   Original Rev.  27-Mar-2015
#                                    Current Rev.   2-Dec-2016
#
#
#
#   This file holds all of the nets for DCDC Converter 8.
#
#   This is the  BULK_3V3  supply   3.300 V  at  12 Amps.
#
#   This Hub Module supply uses a  GE_PDT012  converter.
#


#
#  Connect the converter's  V_Input, V_Output, and Ground  terminals:
#

NET  'ISO_12V'     DCDC8-2


NET  'GROUND'      DCDC8-3   DCDC8-7


NET  'BULK_3V3'    DCDC8-4




#
#  Connect this converter's INPUT Filter:
#

NET  'ISO_12V'   C1361-1   C1362-1   C1363-1   C1364-1
NET  'GROUND'    C1361-2   C1362-2   C1363-2   C1364-2

NET  'ISO_12V'   C1365-1   C1366-1
NET  'GROUND'    C1365-2   C1366-2




#
#  Connect this converter's  OUTPUT  Filter:
#

NET  'BULK_3V3'   C1371-1   C1372-1   C1373-1   C1374-1
NET  'GROUND'     C1371-2   C1372-2   C1373-2   C1374-2

NET  'BULK_3V3'   C1375-1   C1376-1   C1377-1       DZ1351-1
NET  'GROUND'     C1375-2   C1376-2   C1377-2       DZ1351-2





#
#  Ground this converter's unused SYNC terminal:
#

NET  'GROUND'   DCDC8-11




#
#  Connect the  ON_OFF  and  POWER_GOOD  terminals:
#
#  Recall:  The ON_OFF pin is Low active,  i.e. voltage low --> ON.
#           The POWER_GOOD is a common open drain signal
#

NET  'DCDC_8_OFF_ON'        DCDC8-1

NET  'DCDC_8_POWER_GOOD'    DCDC8-10




#
#  Connect the  RAMP_SEQUENCE  terminal:
#
#  Recall:
#
#     The output voltage tracks the scaled Vseq up to set point.
#     R1355 is the 20k Ohm series resistor.
#     R1356 is the scale shunt resistor to ground.


NET  'CONVERTER_RAMP'          R1355-2

NET  'DCDC8_RAMP_SEQUENCE'     R1355-1   R1356-2   C1352-2   DCDC8-9

NET  'DCDC8_SIG_GND'                     R1356-1   C1352-1




#
#  Connect this converter's Output Voltage Control resistor
#  between the  TRIM  and  SIG_GND  terminals:
#

NET  'DCDC8_TRIM'      DCDC8-6    R1352-2

NET  'DCDC8_SIG_GND'   DCDC8-13   R1352-1




#
#  Connect this converter's Remote Sense input
#  terminals  V_SENSE_PLUS  and  V_SENSE_MINUS:
#

NET  'BULK_3V3'   DCDC8-5

NET  'GROUND'     DCDC8-12




#
#  Connect this converter's Servo Loop RC components
#  between the  V_SENSE_PLUS  and  TRIM  terminals:
#

NET  'BULK_3V3'        C1351-1

NET  'DCDC8_LOOP_RC'   C1351-2   R1351-1

NET  'DCDC8_TRIM'                R1351-2




#
#  Connect the PMBus  to this converter and set its address
#  using the  PMBUS_CLK,  PMBUS_DATA,  SMB_ALERT,  ADRS0
#  and  ADRS1  terminals:
#

NET  'Hub_PMBus_SCL'     DCDC8-8

NET  'Hub_PMBus_SDA'     DCDC8-15

NET  'Hubs_SMB_Alert_B'  DCDC8-14

NET  'DCDC8_ADRS_0'      DCDC8-16   R1353-2

NET  'DCDC8_ADRS_1'      DCDC8-17   R1354-2

NET  'DCDC8_SIG_GND'     R1353-1    R1354-1





#
#  Connect the  Power Via Arrays
#

#
#   INPUT Via-Arrays
#

NET  'ISO_12V'    PVA1_dc8-1   PVA1_dc8-2   PVA1_dc8-3
NET  'ISO_12V'    PVA1_dc8-4   PVA1_dc8-5   PVA1_dc8-6

NET  'ISO_12V'    PVA2_dc8-1   PVA3_dc8-1



#
#   GROUND Via-Arrays
#

NET  'GROUND'     PVA4_dc8-1   PVA4_dc8-2   PVA4_dc8-3

NET  'GROUND'     PVA5_dc8-1   PVA6_dc8-1   PVA7_dc8-1

NET  'GROUND'     PVA8_dc8-1   PVA9_dc8-1



#
#   OUTPUT Via-Arrays
#

NET  'BULK_3V3'   PVA10_dc8-1   PVA10_dc8-2   PVA10_dc8-3
NET  'BULK_3V3'   PVA10_dc8-4   PVA10_dc8-5   PVA10_dc8-6

NET  'BULK_3V3'   PVA11_dc8-1   PVA11_dc8-2   PVA11_dc8-3
NET  'BULK_3V3'   PVA11_dc8-4   PVA11_dc8-5   PVA11_dc8-6

NET  'BULK_3V3'   PVA12_dc8-1   PVA13_dc8-1