# # # Backplane No Connect Nets # # Key In Net List file for the Hub Module # -------------------------------------------- # # # # Original Rev. 30-Sept-2015 # Most Recent Rev. 19-Aug-2016 # # # This file holds the "single point nets" for the backplane # connector pins that have No Connection in the Hub Design. # # # Zone 1 Connector P10 with a total of 34 pins # # The Hub Module does not use the following Zone 1 P10 pins: # # - the JTAG connections pins 1:4 # # - the Metalic Test and Ring connections pins 17:24 # # Normally you would expect to see these 12 pins assigned # with "No_Conn" nets but for routing reasons these 12 # pins have been removed from the Geometry for the Zone 1 # connector so they will not appear in the net list at all. # # # Zone 2 Connector J24 with a total of 160 pins # # Base Interface Channels 15 and 16 are not used # because L1Calo uses 14 Slot Shelves. # This is Rows: 9, 10 of J24. # # But we are removing chicklets 9 and 10 # from the J24 connector so we do not # need No_COnn Nets for these 16 pins. # # # Zone 2 Connector J23 with a total of 160 pins # # Base Interface Channel 1 to the Shelf Manager # is not used, as per Dave. The Shelf Manager # will be connected to Ethernet via its front # panel connection. This is Row: 5 of J23. # # Base Interface Channel 2 to the Other Hub # is not used because for routing reasons we # will connect to the Other Hub via pins in # Rows 3 & 4 of J20 in its UpDate Channel area. # We do this to have 2 full criss-cross # Ethernet connections between Hubs. # This is Row: 6 of J23. NET 'No_Conn_J23_A5_BI_ShMCA_DIR' J23-A5 NET 'No_Conn_J23_B5_BI_ShMCA_CMP' J23-B5 NET 'No_Conn_J23_C5_BI_ShMCB_DIR' J23-C5 NET 'No_Conn_J23_D5_BI_ShMCB_CMP' J23-D5 NET 'No_Conn_J23_E5_BI_ShMCC_DIR' J23-E5 NET 'No_Conn_J23_F5_BI_ShMCC_CMP' J23-F5 NET 'No_Conn_J23_G5_BI_ShMCD_DIR' J23-G5 NET 'No_Conn_J23_H5_BI_ShMCD_CMP' J23-H5 NET 'No_Conn_J23_A6_BI_DA2_DIR' J23-A6 NET 'No_Conn_J23_B6_BI_DA2_CMP' J23-B6 NET 'No_Conn_J23_C6_BI_DB2_DIR' J23-C6 NET 'No_Conn_J23_D6_BI_DB2_CMP' J23-D6 NET 'No_Conn_J23_E6_BI_DC2_DIR' J23-E6 NET 'No_Conn_J23_F6_BI_DC2_CMP' J23-F6 NET 'No_Conn_J23_G6_BI_DD2_DIR' J23-G6 NET 'No_Conn_J23_H6_BI_DD2_CMP' J23-H6 # # Zone 2 Connector J20 with a total of 160 pins # # Fabric Interface Channels 14 and 15 are not used # because L1Calo uses 14 Slot Shelves # This is Rows: 8, 7, 6, 5 of J20. # # On J20 the Hub Module does not use: # # Clocks 1, 2, 3 A or B, or Update Channel 4. # These signals are in J20 Rows: 1, 2. # # But for routing reasons we are removing chicklets # 1 and 2 from the J20 connector so we do not need # No_COnn Nets for the 16 signal pins in Rows 1 and 2 # of this connector. # NET 'No_Conn_J20_A8_FI_Tx0_14_DIR' J20-A8 NET 'No_Conn_J20_B8_FI_Tx0_14_CMP' J20-B8 NET 'No_Conn_J20_C8_FI_Rx0_14_DIR' J20-C8 NET 'No_Conn_J20_D8_FI_Rx0_14_CMP' J20-D8 NET 'No_Conn_J20_E8_FI_Tx1_14_DIR' J20-E8 NET 'No_Conn_J20_F8_FI_Tx1_14_CMP' J20-F8 NET 'No_Conn_J20_G8_FI_Rx1_14_DIR' J20-G8 NET 'No_Conn_J20_H8_FI_Rx1_14_CMP' J20-H8 NET 'No_Conn_J20_A7_FI_Tx2_14_DIR' J20-A7 NET 'No_Conn_J20_B7_FI_Tx2_14_CMP' J20-B7 NET 'No_Conn_J20_C7_FI_Rx2_14_DIR' J20-C7 NET 'No_Conn_J20_D7_FI_Rx2_14_CMP' J20-D7 NET 'No_Conn_J20_E7_FI_Tx3_14_DIR' J20-E7 NET 'No_Conn_J20_F7_FI_Tx3_14_CMP' J20-F7 NET 'No_Conn_J20_G7_FI_Rx3_14_DIR' J20-G7 NET 'No_Conn_J20_H7_FI_Rx3_14_CMP' J20-H7 NET 'No_Conn_J20_A6_FI_Tx0_15_DIR' J20-A6 NET 'No_Conn_J20_B6_FI_Tx0_15_CMP' J20-B6 NET 'No_Conn_J20_C6_FI_Rx0_15_DIR' J20-C6 NET 'No_Conn_J20_D6_FI_Rx0_15_CMP' J20-D6 NET 'No_Conn_J20_E6_FI_Tx1_15_DIR' J20-E6 NET 'No_Conn_J20_F6_FI_Tx1_15_CMP' J20-F6 NET 'No_Conn_J20_G6_FI_Rx1_15_DIR' J20-G6 NET 'No_Conn_J20_H6_FI_Rx1_15_CMP' J20-H6 NET 'No_Conn_J20_A5_FI_Tx2_15_DIR' J20-A5 NET 'No_Conn_J20_B5_FI_Tx2_15_CMP' J20-B5 NET 'No_Conn_J20_C5_FI_Rx2_15_DIR' J20-C5 NET 'No_Conn_J20_D5_FI_Rx2_15_CMP' J20-D5 NET 'No_Conn_J20_E5_FI_Tx3_15_DIR' J20-E5 NET 'No_Conn_J20_F5_FI_Tx3_15_CMP' J20-F5 NET 'No_Conn_J20_G5_FI_Rx3_15_DIR' J20-G5 NET 'No_Conn_J20_H5_FI_Rx3_15_CMP' J20-H5