#
#               SWCH_1V2  Supply
#
#            DCDC 5 Converter Nets
#          -------------------------
#
#
#                                   Original Rev.  27-Mar-2015
#                                    Current Rev.   2-Dec-2016
#
#
#
#   This file holds all of the nets for DCDC Converter 5.
#
#   This is the  SWCH_1V2  supply   1.200 V  at  12 Amps.
#
#   This Hub Module supply uses a  GE_PDT012  converter.
#
#   Recall that the SWCH_1V2 rail ramps up after all of
#   the other power buses are up and stable.
#
#   DCDC_5 does not use the analog Ramp Sequence signal.
#


#
#  Connect the converter's  V_Input, V_Output, and Ground  terminals:
#

NET  'ISO_12V'     DCDC5-2


NET  'GROUND'      DCDC5-3    DCDC5-7


NET  'SWCH_1V2'    DCDC5-4




#
#  Connect this converter's INPUT Filter:
#

NET  'ISO_12V'   C1211-2   C1212-2   C1213-2   C1214-2
NET  'GROUND'    C1211-1   C1212-1   C1213-1   C1214-1

NET  'ISO_12V'   C1215-2   C1216-2
NET  'GROUND'    C1215-1   C1216-1




#
#  Connect this converter's  OUTPUT  Filter:
#

NET  'SWCH_1V2'   C1221-1   C1222-1   C1223-1   C1224-1
NET  'GROUND'     C1221-2   C1222-2   C1223-2   C1224-2

NET  'SWCH_1V2'   C1225-1   C1226-1   C1227-1       DZ1201-1
NET  'GROUND'     C1225-2   C1226-2   C1227-2       DZ1201-2





#
#  Ground this converter's unused SYNC terminal:
#

NET  'GROUND'   DCDC5-11




#
#  Connect the  ON_OFF  and  POWER_GOOD  terminals:
#
#  Recall:  The ON_OFF pin is Low active,  i.e. voltage low --> ON.
#           The POWER_GOOD is a common open drain signal
#

NET  'DCDC_5_OFF_ON'        DCDC5-1

NET  'DCDC_5_POWER_GOOD'    DCDC5-10




#
#  Connect the  RAMP_SEQUENCE  terminal:
#
#  Recall:
#
#     DCDC_5  does not use the Ramp Sequence signal.
#     DCDC_5  ramps up after all of the other DCDC
#     converters are up and stable.   DCDC_5 controls
#     its own ramp rate.
#

NET  'No_Conn_DCDC5_Ramp_Sequence'    DCDC5-9




#
#  Connect this converter's Output Voltage Control resistor
#  between the  TRIM  and  SIG_GND  terminals:
#

NET  'DCDC5_TRIM'      DCDC5-6    R1202-2

NET  'DCDC5_SIG_GND'   DCDC5-13   R1202-1




#
#  Connect this converter's Remote Sense input
#  terminals  V_SENSE_PLUS  and  V_SENSE_MINUS:
#

NET  'SWCH_1V2'   DCDC5-5

NET  'GROUND'     DCDC5-12




#
#  Connect this converter's Servo Loop RC components
#  between the  V_SENSE_PLUS  and  TRIM  terminals:
#

NET  'SWCH_1V2'        C1201-1

NET  'DCDC5_LOOP_RC'   C1201-2   R1201-1

NET  'DCDC5_TRIM'                R1201-2




#
#  Connect the PMBus  to this converter and set its address
#  using the  PMBUS_CLK,  PMBUS_DATA,  SMB_ALERT,  ADRS0
#  and  ADRS1  terminals:
#

NET  'Hub_PMBus_SCL'     DCDC5-8

NET  'Hub_PMBus_SDA'     DCDC5-15

NET  'Hubs_SMB_Alert_B'  DCDC5-14

NET  'DCDC5_ADRS_0'      DCDC5-16   R1203-2

NET  'DCDC5_ADRS_1'      DCDC5-17   R1204-2

NET  'DCDC5_SIG_GND'     R1203-1    R1204-1




#
#  Connect the  Power Via Arrays
#

#
#   INPUT Via-Arrays
#

NET  'ISO_12V'    PVA1_dc5-1   PVA1_dc5-2   PVA1_dc5-3
NET  'ISO_12V'    PVA1_dc5-4   PVA1_dc5-5   PVA1_dc5-6

NET  'ISO_12V'    PVA2_dc5-1   PVA3_dc5-1



#
#   GROUND Via-Arrays
#

NET  'GROUND'     PVA4_dc5-1   PVA4_dc5-2   PVA4_dc5-3

NET  'GROUND'     PVA5_dc5-1   PVA6_dc5-1   PVA7_dc5-1

NET  'GROUND'     PVA8_dc5-1   PVA9_dc5-1



#
#   OUTPUT Via-Arrays
#

NET  'SWCH_1V2'   PVA10_dc5-1   PVA10_dc5-2   PVA10_dc5-3
NET  'SWCH_1V2'   PVA10_dc5-4   PVA10_dc5-5   PVA10_dc5-6

NET  'SWCH_1V2'   PVA11_dc5-1   PVA11_dc5-2   PVA11_dc5-3
NET  'SWCH_1V2'   PVA11_dc5-4   PVA11_dc5-5   PVA11_dc5-6

NET  'SWCH_1V2'   PVA12_dc5-1