Run II Timing Signal Generation and Distribution --------------------------------------------- Original Rev. 6-MAY-1997 Most Recent Rev. 26-JUNE-1997 This file describes the Paddle Board that goes on the P3 connection of the TOM card. This card has a standard 160 pin female 90 degree solder tail DIN connector on one side and four 26 pin 4 wall 90 degree solder tail male headers with latches on the opposite side. The following is an outline of the TOM Paddle Board as seen looking at its "component" side. ---------------------------+ / TOP | / +----+-- +----+-- | +----- |O | |O | | | | J2 | | J3 | | +-+----+ | | | | | | | | | TS | | TS | | | | | | 0:4| | 5:7| | | | J1 | +----+-- +----+-- | | | | | | | | +--- +-- +----+- | | | | |O | |O | | | | O | | J4 | | J5 | | All connectors +-+----+ | | | | | are mounted on | | TS | |TS 8, | the Component +----- |9:13| |14,15 | side of the TOM \ +----+-- +----+-- | Paddle Board. \ | ---------------------------+ Connections to the Four Flat Cable Connectors ------------------------------------------------------------------ ---------------- ---------------- ---------------- ---------------- J2 J3 J4 J5 Timing_Sig 0:4 Timing_Sig 5:7 Timing_Sig 8:12 Timing_Sig 13:14 ---------------- ---------------- ---------------- ---------------- Pin Pin Pin Pin Pin Pin Pin Pin Num Fun Num Fun Num Fun Num Fun Num Fun Num Fun Num Fun Num Fun ------- ------- ------- ------- ------- ------- ------- ------- 1 g 2 g 1 g 2 g 1 g 2 g 1 g 2 g 3 TS0+ 4 TS0- 3 via 4 via 3 TS9+ 4 TS9- 3 via 4 via 5 g 6 g 5 g 6 g 5 g 6 g 5 g 6 g 7 TS1+ 8 TS1- 7 TS5+ 8 TS5- 7 TS10+ 8 TS10- 7 TS8+ 8 TS8- 9 g 10 g 9 g 10 g 9 g 10 g 9 g 10 g 11 TS2+ 12 TS2- 11 TS6+ 12 TS6- 11 TS11+ 12 TS11- 11 TS14+ 12 TS14- 13 g 14 g 13 g 14 g 13 g 14 g 13 g 14 g 15 TS3+ 16 TS3- 15 TS7+ 16 TS7- 15 TS12+ 16 TS12- 15 TS15+ 16 TS15- 17 g 18 g 17 g 18 g 17 g 18 g 17 g 18 g 19 TS4+ 20 TS4- 19 via 20 via 19 TS13+ 20 TS13- 19 via 20 via 21 g 22 g 21 g 22 g 21 g 22 g 21 g 22 G 23 g 24 g 23 g 24 g 23 g 24 g 23 g 24 G 25 g 26 g 25 g 26 g 25 g 26 g 25 g 26 G Layout of the TOM's J3 Timing Signal Inputs: ---------------------------------------------- TOM's J3 LAYOUT ---------------------------------------------------------------- Pin Row Row Row Row Row Number "A" "B" "C" "D" "E" ------ --------- --------- ------- ------- ------- 1 Gnd Gnd Gnd Gnd N.C. 2 TS_00_INV TS_00_NON +3V Gnd N.C. 3 Gnd Gnd Gnd Gnd N.C. 4 TS_01_INV TS_01_NON +3V Gnd N.C. 5 Gnd Gnd -4.5V Gnd N.C. 6 TS_02_INV TS_02_NON Gnd Gnd N.C. 7 Gnd Gnd +3V Gnd N.C. 8 TS_03_INV TS_03_NON Gnd Gnd N.C. 9 Gnd Gnd +5V Gnd N.C. 10 TS_04_INV TS_04_NON Gnd Gnd N.C. 11 Gnd Gnd +3V Gnd N.C. 12 TS_05_INV TS_05_NON Gnd Gnd N.C. 13 Gnd Gnd +3V Gnd N.C. 14 TS_06_INV TS_06_NON Gnd Gnd N.C. 15 Gnd Gnd -4.5V Gnd N.C. 16 TS_07_INV TS_07_NON Gnd Gnd N.C. 17 Gnd Gnd +3V Gnd N.C. 18 TS_08_INV TS_08_NON Gnd Gnd N.C. 19 Gnd Gnd +5V Gnd N.C. 20 TS_09_INV TS_09_NON +3V Gnd N.C. 21 Gnd Gnd Gnd Gnd N.C. 22 TS_10_INV TS_10_NON +3V Gnd N.C. 23 Gnd Gnd Gnd Gnd N.C. 24 TS_11_INV TS_11_NON -4.5V Gnd N.C. 25 Gnd Gnd Gnd Gnd N.C. 26 TS_12_INV TS_12_NON +3V Gnd N.C. 27 Gnd Gnd Gnd Gnd N.C. 28 TS_13_INV TS_13_NON +5V Gnd N.C. 29 Gnd Gnd +3V Gnd N.C. 30 TS_14_INV TS_14_NON Gnd Gnd N.C. 31 Gnd Gnd +3V Gnd N.C. 32 TS_15_INV TS_15_NON Gnd Gnd N.C. Design Details -------------- The card is 2.5" x 4.3" Physical Layer Order Logical Layer ---------- ----- -------------------------------- Physical_1 1 Pad_1, Signal_1 Physical_2 2 Power_1 Physical_3 3 Pad_2, Signal_2 Artwork Order Logical Layers ------- ----------------------------- -------------------------- 1 Board_Outline, Dam_1, Target Test Plot 2 Signal_1, Pad_1, Target 3 Power_1, Target Thermo Relief Clr 50 mil 4 Signal_2, Pad_2, Target 5 Silkscreen_1, Target 6 SolderMask_1, Target DAM_1 is the target area label for the board outline test plot. SolderMask Pen Table ------------------------- D10 10 mil D12 65 mil Holes Finished Size -------------------------- 38 mil x 274 106 mil x 12 Hand copy the following files to the ../tom_pb_uber/copy_to_flop_dir Tom_Pabble_Brd_Aperture_Table_Report.txt --> aperture.txt Tom_Pabble_Brd_Drill_Table_Report.txt --> drill.txt Tom_Pabble_Brd_Manufacture_Instructions.txt --> instruct.txt