Run 2 Paddle Card Inventory ------------------------------- Original Rev. 30-JUL-1997 Most Recent Rev. 7-FEB-2000 The intent of this file is to capture inventory information about circuit cards that are being built for Run 2. Eventually we plan to have a formal inventory system and trailer sheets for all of our Run 2 hardware. Auxiliary and Paddle Board Cards: --------------------------------------- Rev. 4-NOV-1997 Card Type Quantity and Characteristics ----------- ----------------------------------------------------- TOM_PB Quantity = 20 No surface mount Components: 4x 26 pin 90 deg solder tail header with latches 1x 160 pin 90 deg solder tail female DIN connector CARMEN_PB Quantity = 20 No surface mount Components: 3x 26 pin 90 deg solder tail header without latches 1x 96 pin 90 deg solder tail female DIN connector FRONT_PB Quantity about 75 No surface mount Components: 4x 34 pin 90 deg solder tail header with latches 1x 160 pin 90 deg solder tail male DIN connector PASS-THROUGH Quantity about 25 No surface mount Components: 8x 34 pin 90 deg solder tail header with latches 3x 160 pin 90 deg solder tail female DIN connector RAY Quantity = 20 Surface mount two 16 pin SOIC resistor networks, six 1206 ceramic capacitors, and one tantalum capacitor. All 20 RAY cards will use the same value resistor networks. Components: 1x 160 pin 90 deg solder tail female DIN connector 6x 0.1 uFd 50 Volt Z5U ceramic cap 1206 size 1x tant 2x 100 Ohm 16 pin SOIC resistor network ?x 330/470 Ohm 10 pin SIP VME Terminator ResNets REAR_PB Quantity about 125 Surface mount eight 16 pin SOIC resistor networks. Only some of the REAR_PB cards will have these resistor networks installed. Two or three different values of the resistor networks may be used. Only some of the REAR_PB cards will have the four 34 pin connectors installed. The cards without the 34 pin connectors must be taped to keep solder out of the via's for these connectors. Approximate Install the 34 Resistor Quantity Pin Connectors Network Value ----------- -------------- ------------- 25 Yes 110 Ohm 25 Yes 1k Ohm 25 No 110 Ohm 50 No 1k Ohm Components: 1x 160 pin 90 deg solder tail female DIN connector for ? of the TRM 8x Resistor Array 110 Ohm for ? of the TRM 8x Resistor Array 1000 Ohm for ? of the TRM 4x 34 pin 90 deg solder tail header with latches for ? of the TRM 4x 34 pin straight WW tail header with latches for ? of the TRM 4x 32 pin straight press in ??mm tail header without latches TRM_PB Quantity = 20 There is no example of this board available yet. But, it will look exactly like the REAR_PB card. Surface mount eight 16 pin SOIC resistor networks. All 20 cards will use the same value of resistor network. All 20 cards will have the 40 pin connectors installed. Components: 1x 160 pin 90 deg solder tail female DIN connector 8x Resistor Array 110 Ohm 2x 40 pin 90 deg solder tail header with latches support cards common parts list Qty Have Qty Item Description and Manufacturer's Part Number 23OCT97 Need ------------------------------------------------ ------- ------- 96 pin 90 deg solder tail Female DIN connector 20 20 Carmen AMP 650461-4 end Total 20 160 pin 90 deg solder tail Female DIN connector 200 20 TOM ERNI 013-167 45x3=135 PTru 20 Ray 150 Rear 25 TRM end Total 350 160 pin 90 deg solder tail Male DIN connector 48 85 FRONT ERNI 004-778 end Total 85 26 pin 90 deg solder tail header with latches 60 20x4=80 TOM AMP 499141-6 AMP 102160-6 end Total 80 26 pin 90 deg solder tail header without latches 46 20x3=60 Carmen TB 609-2607 AMP 103311-6 end Total 60 34 pin 90 deg solder tail header with latches 21 85x4=340 Front AMP 499141-8 AMP 102160-8 45x4=180 PTru ? Rear end Total ? 32 pin straight 5.5mm tail B/2 connector 100 Rear ERNI 414-313 hole 39.4mil +3.5mil -2.4mil 32 pin straight 13mm tail B/2 connector 60 Rear Panduit 100-632-951 hole 40mil +3mil -3mil 32 pin straight 17mm tail B/2 connector 100 Rear Panduit 100-632-959 hole 40mil +3mil -3mil 32 pin straight 17mm tail B/2 connector 250 Rear ERNI 414-310 hole 39.4mil +3.5mil -2.4mil 40 pin 90 deg solder tail header with latches 30 25x2=50 TRM AMP 102346-9 AMP 102160-9 end Total 50 Resistor Array 110 Ohm ? ?x8= ? Rear 25x8=200 TRM end Total ? 30-OCT-97 Quantity Quantity Estimate 30-OCT-97 30-OCT-97 Estimated Needed to Spares TOTAL Given to Run Fermi Quantity Quantity Easy to Card Safari plus MSU Estimate Estimate Launch ----------- ---------- --------- --------- -------- ------- TOM_PB 20 20 0 20 Y CARMEN_PB 20 20 0 20 Y FRONT_PB about 75 70 15 85 Y- PASS-THROUGH about 25 38 7 45 Y- RAY 20 20 0 20 Y- REAR_PB (total) about 125 132 18 ? 150 ? N TRM_PB 20 25 0 25 Y- BUILD Lists Build of 20 TOM Paddle Boards ------------------------------- TOM_PB Parts List for 20 cards No Surface Mount Parts Quantity Item Description -------- ------------------------------------------------ 20 TOM raw circuit boards 20 160 pin 90 deg solder tail female DIN connector ERNI Part No. 013-167 80 26 pin 90 deg solder tail header with latches AMP Part No. AMP 499141-6 or AMP 102160-6 240 M2.5 10mm Screw Hex Nut sets Build of 20 CARMEN Paddle Boards ---------------------------------- CARMEN Parts List for 20 cards No Surface Mount Parts Quantity Item Description -------- ----------------------------------------------- 20 CARMEN raw circuit boards 20 96 pin 90 deg solder tail female DIN connector AMP Part No. 650461-4 60 26 pin 90 deg solder tail header without latches Thomas & Betts Part No. 609-2607 40 M2.5 10mm Screw Hex Nut sets Build of 17 FRONT Paddle Boards --------------------------------- FRONT_PB Parts List for 17 cards No Surface Mount Parts Quantity Item Description -------- ----------------------------------------------- 17 FRONT raw circuit boards 17 160 pin 90 deg solder tail male DIN connector ERNI Part No. 004-778 68 34 pin 90 deg solder tail header with latches AMP Part No. AMP 499141-8 or AMP 102160-8 204 M2.5 10mm Screw Hex Nut sets Build of 19 PASS-THROUGH Boards --------------------------------- PASS-THROUGHM Parts List for 19 cards No Surface Mount Parts Quantity Item Description -------- ------------------------------------------------ 19 PASS-THROUGH raw circuit boards 38 160 pin 90 deg solder tail female DIN connector ERNI Part No. 013-167 NOTE: This 160 pin connector is installed at locations J2 and J3 ONLY. J1 is empty. 152 34 pin 90 deg solder tail header with latches AMP Part No. AMP 499141-8 or AMP 102160-8 456 M2.5 10mm Screw Hex Nut sets Build of 19 RAY Boards ------------------------ RAY Parts List for 19 cards Quantity Item Description -------- ------------------------------------------------ 19 RAY raw circuit boards 19 160 pin 90 deg solder tail female DIN connector ERNI Part No. 013-167 114 0.1 uFd 50 Volt Z5U ceramic cap 1206 size 19 tantalum cap 38 39 Ohm 16 pin SOIC resistor network 190 330/470 Ohm 10 pin SIP VME Terminator ResNets 76 M2.5 10mm Screw Hex Nut sets :::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::: 2-FEB-1998 Receive from Hughes the following Paddle Boards CARMEN_PB Qty = 20 TOM_PB Qty = 17 PASS_THROUGH Qty = 18 FRONT_PB Qty = 80 RAY_Term Qty = 19 16-MARCH-1998 Receive from Hughes the following Paddle Boards PASS_THROUGH Qty = 26 FRONT_PB Qty = 1 Also received all of the proto-type demo boards back from Hughes and all of the extra parts that had been shipped to them. 19-OCT-1998 Receive from Hughes the following Paddle Boards and all the extra parts from the fall 1998 PB build: TRM Qty = 50 Per Bnch SM Qty = 80 Gated SM Qty = 50 TDM Qty = 30 Rear PB with Terminators Qty = 30 Rear PB without Terminators Qty = 70 4-FEB-2000 Receive from Hughes the following Paddle Boards and all the extra parts from the JAN 2000 PB build: Front PB Qty = 15 Rear PB: with Connectors with Resistors Qty = 25 Rear PB: with Connectors without Resistors Qty = 15 Rear PB: without Connectors with Resistors Qty = 15 Rear PB: without Connectors without Resistors Qty = 10