!===============================================================================
! ADF Et Lookup Coefficients
!
! This file is %CONFIG%L1Cal_IIb_Lookup_Coeffs.tti
! This file is called by Boot_Auxi_Adf.mcf
! 
! This file controls the Lookup coefficients to convert Filtered E values
! into Output Et values sent to the TABs
!
!------------------------------------------------------------------------------
! Comments start with an exclamation mark ("!") anywhere on a line.
!------------------------------------------------------------------------------
! Revision: 23-May-2006 initial values
!===============================================================================


!--------------------------------------------------------------------
! Define some cosmetic constants to make the rest easier to read

! Trigger Tower Channel Type
$TT_EM_Channel= 0
$TT_HD_Channel= 1

! Trigger Tower Eta Sign 
$TT_Eta_Pos= 0
$TT_Eta_Neg= 1

!---------------------------
! Define EM Et Lookup Coefficients
!---------------------------

TT_Channel: $TT_EM_Channel  

    TT_Eta_Sign: $TT_Eta_Pos    To_TT_Eta_Sign: $TT_Eta_Neg

      TT_Phi: 1    To_TT_Phi: 32       

      ! Zero Energy Response for ADC and Filtered E (i.e. input of lookup)
        TT_Eta_Magn: 1    To_TT_Eta_Magn: 20       

            Zero_Energy_Adc_E:      50   
 
      ! Zero Energy Response of Ouput Et (i.e. output of lookup)
        TT_Eta_Magn: 1    To_TT_Eta_Magn: 18       

            Zero_Energy_Output_Et:  8    

        TT_Eta_Magn: 19    To_TT_Eta_Magn: 20     ! Eta 19 and 20 correspond to the ICR

            Zero_Energy_Output_Et:  0             ! these signals get added to others, 
                                                  ! and must thus not add any offset
           

    ! The Slope is eta dependent.
    ! For this initial setup the slope is independent of the sign of eta.
    ! For this initial setup we will set the slope of  TT_Etas 19, 20  to
    ! mid scale.  TT_Eta 19 and 20 are the massless gap and ICD signals.

        TT_Eta_Magn:  1    Lookup_Slope:   0.4564
        TT_Eta_Magn:  2    Lookup_Slope:   0.4380
        TT_Eta_Magn:  3    Lookup_Slope:   0.4076
        TT_Eta_Magn:  4    Lookup_Slope:   0.3640
        TT_Eta_Magn:  5    Lookup_Slope:   0.4252
        TT_Eta_Magn:  6    Lookup_Slope:   0.3692
        TT_Eta_Magn:  7    Lookup_Slope:   0.2668
        TT_Eta_Magn:  8    Lookup_Slope:   0.2388
        TT_Eta_Magn:  9    Lookup_Slope:   0.4980
        TT_Eta_Magn: 10    Lookup_Slope:   0.4128
        TT_Eta_Magn: 11    Lookup_Slope:   0.3408
        TT_Eta_Magn: 12    Lookup_Slope:   0.2768
        TT_Eta_Magn: 13    Lookup_Slope:   0.3024
        TT_Eta_Magn: 14    Lookup_Slope:   0.2460
        TT_Eta_Magn: 15    Lookup_Slope:   0.7360
        TT_Eta_Magn: 16    Lookup_Slope:   0.6024
        TT_Eta_Magn: 17    Lookup_Slope:   0.4384
        TT_Eta_Magn: 18    Lookup_Slope:   0.2824
        TT_Eta_Magn: 19    Lookup_Slope:   0.4
        TT_Eta_Magn: 20    Lookup_Slope:   0.4


!---------------------------
! Define HD Et Lookup Coefficients
!---------------------------

TT_Channel: $TT_HD_Channel  

    TT_Eta_Sign: $TT_Eta_Pos    To_TT_Eta_Sign: $TT_Eta_Neg

      TT_Phi: 1    To_TT_Phi: 32       

      ! Zero Energy Response for ADC and Filtered E (i.e. input of lookup)
        TT_Eta_Magn: 1    To_TT_Eta_Magn: 20       

            Zero_Energy_Adc_E:      50   ! Zero Energy Response of the ADC and
                                         ! Filtered E data.  This is the input
                                         ! address to the Et Lookup Memory.

 
      ! Zero Energy Response of Ouput Et (i.e. output of lookup)
        TT_Eta_Magn: 1    To_TT_Eta_Magn: 18       

            Zero_Energy_Output_Et:   8   ! Zero Energy Response of the ADF-2
                                         ! Output Et data to the TAB.  This is
                                         ! the output data from the Et Lookup
                                         ! Memory.


        TT_Eta_Magn: 19    To_TT_Eta_Magn: 20     ! Eta 19 and 20 correspond to the ICR

            Zero_Energy_Output_Et:  0    ! these signals get added to others, 
                                         ! and must thus not add any offset
           

    ! The Slope is eta dependent.
    ! For this initial setup the slope is independent of the sign of eta.
    ! For this initial setup we will set the slope of  TT_Etas 19, 20  to
    ! mid scale.  TT_Eta 19 and 20 are the massless gap and ICD signals.

        TT_Eta_Magn:  1    Lookup_Slope:   0.5524
        TT_Eta_Magn:  2    Lookup_Slope:   0.5312
        TT_Eta_Magn:  3    Lookup_Slope:   0.4552
        TT_Eta_Magn:  4    Lookup_Slope:   0.4124
        TT_Eta_Magn:  5    Lookup_Slope:   0.6176
        TT_Eta_Magn:  6    Lookup_Slope:   0.5836
        TT_Eta_Magn:  7    Lookup_Slope:   0.2604
        TT_Eta_Magn:  8    Lookup_Slope:   0.2928
        TT_Eta_Magn:  9    Lookup_Slope:   0.5472
        TT_Eta_Magn: 10    Lookup_Slope:   0.4592
        TT_Eta_Magn: 11    Lookup_Slope:   0.3416
        TT_Eta_Magn: 12    Lookup_Slope:   0.2784
        TT_Eta_Magn: 13    Lookup_Slope:   0.3060
        TT_Eta_Magn: 14    Lookup_Slope:   0.2492
        TT_Eta_Magn: 15    Lookup_Slope:   0.7848
        TT_Eta_Magn: 16    Lookup_Slope:   0.6424
        TT_Eta_Magn: 17    Lookup_Slope:   0.4348
        TT_Eta_Magn: 18    Lookup_Slope:   0.2336
        TT_Eta_Magn: 19    Lookup_Slope:   0.4
        TT_Eta_Magn: 20    Lookup_Slope:   0.4