Disco-Kraken Board  THD  Components
         -------------------------------------


        For Bid Only  -  NOT Good for Production
       ------------------------------------------


                                         Rev.  28-Aug-2024


The purpose of this note is to describe all of the  Through
Hole Device  (THD)  components that the assembly vendor
needs to mount onto the Disco-Kraken circuit board.

The Disco-Kraken uses  9  types of THD components.  The
following tables lists all of the THD components, how many
of each type are used, and their reference designators.



MSU Disco-Kraken        THD  Component:  Description,
   Part Number       Vendor Part No  &  Reference Desig.     Count
----------------    -------------------------------------    -----

Cap_10_uFd_250V_Poly    Polypropylene Capacitor                 2
                        10 uFd  250 Volt
                        Kemet Part No.  R75IR51004040J
                        Ref Desigs:  C1653, C1656


3M_3314-5302            Header  14 Pin  2x7  0.1" x 0.1"        1
                        Right-Angle  4 Wall
                        3M Part No.  N3314-5302RB
                        Ref Desigs:  J7


3M_3408-5303            Header  16 Pin  2x8  0.1" x 0.1"        1
                        Right-Angle  4 Wall
                        3M Part No.  N3408-5303RB
                        Ref Desigs:  J1


Harwin_M80_MH313M5_08   Connector  Coaxial  8 Position          2
                        24 Pins plus 2 Screws  Right-Angle
                        Harwin Part No.  M80-MH313M5-08
                        Ref Desigs:  J2, J3


Molex_87833_4020        Connector  40 Pin  Right-Angle  2mm     2
                        4 Wall  Milli-Grid
                        Molex Part No.  87833_4020
                        Ref Desigs:  J4, J5


Molex_USB_482040001     Connector  USB Type A                   2
                        Right-Angle
                        Molex Part No.  482040001
                        Ref Desigs:  J15, J16


PTH04T230WAD            DCDC Power Converter  6 Amps            2
                        TI Part No.  PTH04T230WAD
                        Ref Desigs:  DCDC2, DCDC3


PTH04T260WAD            DCDC Power Converter  3 Amps            4
                        TI Part No.  PTH04T260WAD
                        Ref Desigs:  DCDC1, DCDC4, DCDC5, DCDC6


TRACO_TEN20_7211WIR     DCDC Power Converter  20 Watt           1
                        Traco Power Part No.  TEN 20-7211WIR
                        Ref Desigs:  DCDC20


Concerns about the THD components:

 - The 2 large Polypropylene Capacitor  C1653 and C1656  need
   to be installed with a 90 degree bend in their leads so that
   they lay with their flat surface against the marked area on
   the circuit board.  These 2 capacitors will be the tallest
   components on the board.  Is there some way to glue them to
   the circuit board so that they stay in place ?   I do not
   want any vibration during use to cause them to rise up above
   the circuit board surface.

 - 2 types of the DCDC Converters,  PTH04T230WAD  and
   PTH04T260WAD  look almost exactly alike and can plug into
   each others  hole patterns in the circuit board.  It would
   be easy to get them mixed up during hand installation.

 - Some of the THD connectors listed above include mounting
   screws in addition to their soldered electrical terminals.
   Will the assembly vendor want us to supply these screws,
   washers, and nuts so that they can firmly mount these
   connectors in place before the soldering operation  or
   should this stainless steel hardware be kept away from
   the soldering operation to prevent contamination ?